Doing this to accomodate some really long warning text in a
checkbox widget. Needs 5 lines for English. Probably a lot
more for German, etc., so increasing it to 10 lines.
Please don't abuse that. 4 lines is still a reasonable max.
Change-Id: Ife5858f2165cb2bc046ce606f29d31010d26ecc2
Watches for package changes so it can dynamically adjust
to reflect the actual list of available activities.
Change-Id: I3a2fef3dac4d13d1b2a7ed6fc117a7b814679669
1. The NumberPicker was showing the IME if the input field
gets focus and hiding it when the the arrows are pressed.
The leads to a nasty behavior when the input is the first
focusable and the uses presser an arrow button. In such
a case the IME shows and hides on every arrow press pushing
the window content up and down - this looks pretty ugly.
Now the IME is show on double tap of the input field.
2. The NumberPicker input now by default has an IME action
done, hence after editing it the IME goes away.
3. The NumberPicker input now clears focus when it gets
IME action done, so the last picker in a sequence
does not show selection which is focus driven.
4. NumberPicker was incorrectly detecting double tap to
begin edit and it was possble to start edit on singe tap
if the user has double tapped before to start an edit.
Now double tap detection is using the double tap timeout
correctly.
bug:6071977
Change-Id: I0ff5a491064e51663b3abec675d839d0a65b986a
My previous change to speed up the time the IME is dismissed was
fundamentally flawed. That change basically switched the order
the application called the input method manager service from doing
startInput() and then windowGainedFocus(), to first windowGainedFocus()
and then startInput().
The problem is that the service relies on startInput() being done
first, since this is the mechanism to set up the new input focus,
and windowGainedFocus() is just updating the IME visibility state
after that is done. However, by doing the startInput() first, that
means in the case where we are going to hide the IME we must first
wait for the IME to re-initialize editing on whatever input has
focus in the new window.
To address this, the change here tries to find a half-way point
between the two. We now do startInput() after windowGainedFocus()
only when this will result in the window being hidden.
It is not as easy as that, though, because these are calls on to
the system service from the application. So being able to do that
meant a fair amount of re-arranging of this part of the protocol
with the service. Now windowGainedFocus() is called with all of
the information also needed for startInput(), and takes care of
performing both operations. The client-side code is correspondingly
rearranged so that the guts of it where startInput() is called can
instead call the windowGainedFocus() entry if appropriate.
So... in theory this is safer than the previous change, since it
should not be impacting the behavior as much. In practice, however,
we are touching and re-arranging a lot more code, and "should" is
not a promise.
Change-Id: Icb58bef75ef4bf9979f3e2ba88cea20db2e2c3fb
Remove the right-to-left cascade effect from action mode menu
items. Animation time is now fixed at 300ms for scaling in menu items.
Change-Id: I8eef2ed9f93c2af804663dd5e6b3f4915ed45cb1
This adjust various paths through InputMethodManager so that the flow
in switching focus from one application to another is cleaner, resulting
in less work being done, resulting in it being able to happen quicker.
Some of the changes here avoid doing stuff when not needed, such as when
we are told to unbind but are not currently the active input. A big part
is also a change to the flow when a window receives input. Previously
this would first do a checkFocus() which would tell the input method to
switch focus to whatever view has focus in the window, followed by the
windowGainedFocus() call telling it the window had gained focus. This
would result in extra work because the input method service would first
handle the focus switch, seeing the IME is currently displayed, so the IME
would remain up and reset its focus to the new view. The app would
immediately then tell it about the window, causing the service to find out
the IME should be hidden and telling the IME, but the IME couldn't hide
itself until it had first take care of switching its input.
There is the definite potential of this breaking IME showing/hiding in
cases depending on the order things may be relying on them to happen. I
haven't seen any problems with a brief trip through the UI.
Change-Id: I8494cbd6e19e2ab6db03f2463d9906680dda058b
Since CDMA doesn't use APN settings there was no place to say what a cdma
device's DUN connection would support, so by default normal device
originating traffic would be blocked on a tethering single-connection device.
With this change you can (via overlay) say that it supports everything
so mms and on-device browsing/email will still work even when on a dun connection.
The reason to allow both: some carriers will charge per byte for dun access
and so they don't want lots of non-tethering traffic used (costs the user alot)
but other carriers just use a dun connection to limit access to tethering, but
once there give unlimited data, so it makes sense to support everything there.
bug:5972599
Change-Id: I78fd7f3ac63c51a0560b659ed5ec219b10a93f8d
This patch is adding a capability so that OEM can override USB mode
in case the device is boot up with OEM specific mode. (i.e. modem
debug, factory test etc.)
Bug:5964042
Change-Id: Ic8e23d302563ce71eedb74ce94cca8c65838a4f7
fully documenting the device default themes and fixing many more,
including adding API level information for older themes to avoid confusion.
Oh and fix an unclosed <em> tag causing a format bug.
Change-Id: Ia4b33559bd5ad2cbae8b53966999cf7f5038b125
Don't consider a window as a candidate for the top fullscreen window
if it is not going to be a candiate for layout.
This fix does not include the change to ignore app tokens that are
hidden. This causes problems in some dialogs that stay hidden until
their app is ready to display, but need to perform a series of relayouts
during that time to get to the right size. Dropping this part of
the change still (mostly?) seems to allow us to avoid the bad states.
Change-Id: Ic052cb1499d3287f47e9ffeac5cd2470ee5a308c
Also relaxed the settle time constraints a little bit.
With this change, a rotation proposal will always be
advertised within 500ms even if the device is still shaking
around.
Bug: 5496491
Change-Id: I0bf562f4c19c0be45c016254f2f881d265f8e266
This fixes a bug where the device fails to lock when DevicePolicyManagerService
requests the device to be locked and the screen was off because the user hit
the power button.
The change allows DPMS to directly invoke screen lock, bypasssing the screen state.
Change-Id: Iecdda6fc61e9c519119de495be23c69c3b983921
incorrectly specified.
This affected search bars and alert dialogs spawned from activities
using Theme.DeviceDefault.Light as a base.
Change-Id: I219d38d486498db5b4b283560256afd7d6051535
